Model:606B01 - Ring-style, industrial, ceramic shear ICP® accel, 100 mV/g, 0.5 to 10k Hz, side exit, 2-pin connector, single point ISO 17025 accredited calibration_1149678
Representative image only

Model:606B01 - Ring-style, industrial, ceramic shear ICP® accel, 100 mV/g, 0.5 to 10k Hz, side exit, 2-pin connector, single point ISO 17025 accredited calibration

$1,102.85

The price is inclusive of GST
Broadband Resolution (1) (English)350 µg
Broadband Resolution (1) (SI)3434 µm/sec<sup>2</sup>
Constant Current Excitation2 to 20 mA
Discharge Time Constant≥0.3 sec
Electrical Connection PositionSide
Electrical Connector2-Pin MIL-C-5015
Electrical Isolation (Case)>100000000 Ohm
Enclosure RatingIP68
Excitation Voltage18 to 28 VDC
Frequency Range (±3 dB) (English)30 to 600000 cpm
Frequency Range (±3 dB) (SI)0.5 to 10000 Hz
Housing MaterialStainless Steel
Measurement Range (English)±50 g
Measurement Range (SI)±490 m/s²
MountingThrough Hole
Mounting Thread (English)1/4-28 Male
Mounting Thread (SI)Not Applicable
Mounting Torque (English)2 to 5 ft-lb
Mounting Torque (SI)2.7 to 6.8 Nm
Non-Linearity±1 %
Output Bias Voltage8 to 12 VDC
Output Impedance<150 Ohm
Overload Limit (Shock) (English)5000 g pk
Overload Limit (Shock) (SI)49050 m/s² pk
Resonant Frequency (English)1500 kcpm
Resonant Frequency (SI)25 kHz
SealingWelded Hermetic
Sensing ElementCeramic
Sensing GeometryShear
Sensitivity (±20 %) (English)100 mV/g
Sensitivity (±20 %) (SI)10.2 mV/(m/s²)
Settling Time (within 1% of bias)≤2.0 sec
Size - Diameter (English)1.38 in
Size - Diameter (SI)35.1 mm
Size - Height (English)1.00 in
Size - Height (SI)25.4 mm
Spectral Noise (1 kHz) (English)4 µg/√Hz
Spectral Noise (1 kHz) (SI)39.2 (µm/sec<sup>2</sup>)/√Hz
Spectral Noise (10 Hz) (English)8 µg/√Hz
Spectral Noise (10 Hz) (SI)78.5 (µm/sec<sup>2</sup>)/√Hz
Spectral Noise (100 Hz) (English)5 µg/√Hz
Spectral Noise (100 Hz) (SI)49.1 (µm/sec<sup>2</sup>)/√Hz
Temperature Range (English)-65 to +250 °F
Temperature Range (SI)-54 to +121 °C
Transverse Sensitivity≤7 %
Weight (English)4.4 oz
Weight (SI)124 gm
Drawing (PDF)
Product Manual (PDF)
Specifications (PDF)
Overview
Low-cost Industrial ICP® Accelerometer
Ring-style, industrial, ceramic shear ICP® accelerometer, 100 mV/g, 0.5 to 10k Hz, side exit, 2-pin connector, single point ISO 17025 accredited calibration


Product Specifications
 ENGLISHSI 
Performance
    Sensitivity (±20 %) 100 mV/g10.2 mV/(m/s²)[1] 
    Measurement Range±50 g±490 m/s² 
    Frequency Range (±3 dB)30 to 600000 cpm0.5 to 10000 Hz[4] 
    Resonant Frequency1500 kcpm25 kHz[2] 
    Broadband Resolution (1)350 µg3434 µm/sec2[2] 
    Non-Linearity±1 %±1 %[3] 
    Transverse Sensitivity≤7 %≤7 % 
Environmental
    Overload Limit (Shock)5000 g pk49050 m/s² pk 
    Temperature Range-65 to +250 °F-54 to +121 °C 
    Enclosure RatingIP68IP68 
Electrical
    Settling Time (within 1% of bias)≤2.0 sec≤2.0 sec 
    Discharge Time Constant≥0.3 sec≥0.3 sec 
    Excitation Voltage18 to 28 VDC18 to 28 VDC 
    Constant Current Excitation2 to 20 mA2 to 20 mA 
    Output Impedance<150><150> 
    Output Bias Voltage8 to 12 VDC8 to 12 VDC 
    Spectral Noise (10 Hz)8 µg/√Hz78.5 (µm/sec2)/√Hz[2] 
    Spectral Noise (100 Hz)5 µg/√Hz49.1 (µm/sec2)/√Hz[2] 
    Spectral Noise (1 kHz)4 µg/√Hz39.2 (µm/sec2)/√Hz[2] 
    Electrical Isolation (Case)>100000000 Ohm>100000000 Ohm 
Physical
    Size - Diameter1.38 in35.1 mm 
    Size - Height1.00 in25.4 mm 
    Weight4.4 oz124 gm 
    MountingThrough HoleThrough Hole 
    Mounting Thread1/4-28 MaleNot Applicable[5] 
    Mounting Torque2 to 5 ft-lb2.7 to 6.8 Nm 
    Sensing ElementCeramicCeramic 
    Sensing GeometryShearShear 
    Housing MaterialStainless SteelStainless Steel 
    SealingWelded HermeticWelded Hermetic 
    Electrical Connector2-Pin MIL-C-50152-Pin MIL-C-5015 
    Electrical Connection PositionSideSide 

All specifications are at room temperature unless otherwise specified.

CEceneleccsa_us
Product Notes
[1] Conversion Factor 1g = 9.81 m/s².
[2] Typical.
[3] Zero-based, least-squares, straight line method.
[4] The high frequency tolerance is accurate within ±10% of the specified frequency.
[5] 1/4-28 has no equivalent in S.I. units.
[6] See PCB Declaration of Conformance PS023 or PS060 for details.
Accessories:
Supplied
081A68Captive mounting bolt 1/4-28 x .90"(1)
ICS-2NIST-traceable single-axis single-point amplitude response calibration at 6000 cpm (100 Hz)(1)
Optional Versions:
(EX) Hazardous Area Approval- contact factory for specific approvals
 ENGLISHSI
    Hazardous Area ApprovalEx ia IIC T4, AExia IIC, T4Ex ia IIC T4, AExia IIC, T4
    Hazardous Area ApprovalEEx nL IIC T4, -40°C<><=121â°c, ii="" 3="">EEx nL IIC T4, -40°C<><=121â°c, ii="" 3="">
    Hazardous Area ApprovalEEx nL IIC T4, -40°C<><=121â°c, ii="" 1="">EEx nL IIC T4, -40°C<><=121â°c, ii="" 1="">
    Hazardous Area ApprovalCl I, Div I, Groups A, B, C, D; Cl II, Div I, Groups E, F, G; Cl III, Div ICl I, Div I, Groups A, B, C, D; Cl II, Div I, Groups E, F, G; Cl III, Div I
    Hazardous Area ApprovalCl I, Div 2, Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4Cl I, Div 2, Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4
(M) Metric Mount
 ENGLISHSI
Accessories:
    M081A68Captive Mounting Bolt(1)

Over 40,000 Customers Trust John Morris